SERVICE, RESTORATION, TRANSFORMATION

THE HOT BLUING SERVICE SHOULD BE PERFORMED EVERY 7-10 YEARS ON ALL 1931 MODEL FABRIQUE NATIONALE 6.35MM, PSP-25 AND PSA-25 HOT BLUED POCKET PISTOLS. DOING SO IS OF COURSE DEPENDENT ON THE CONDITION OF THE UNDERLYING 8620 STEEL ALLOY SURFACE AND THE BLUE FINISH OF THE PISTOL.

FOLKS OFTEN INSTRUCT US TO PERFORM THE HOT BLUING SERVICE WHEN THEY ACQUIRE A USED 1931 MODEL FN 6.35MM, PSP-25 OR PSA-25 POCKET PISTOL. AND THEY OFTEN DO SO AT THE SAME TIME THEY HAVE US UNDERTAKE THE SPRING REPLACEMENT SERVICE. NOW IS ALSO A GOOD TIME TO PURCHASE 1-3 MAGAZINES FROM US.

PROJECT SCOPE:

WHAT IS DESCRIBED BELOW PERTAINS SPECIFICALLY TO THE RESURFACING, HOT BLUING AND REBUILDING OF A "STANDARD" MODEL 1931 FN 6.35MM, PSP-25 OR PSA-25 6 SHOT HOT BLUED POCKET PISTOL. REACH OUT TO US IF YOUR HAVE A DIFFERENT MODEL. THE PROCESS AND PRICING MAY BE DIFFERENT.

THE PISTOL IS DIS-ASSEMBLED INTO ITS COMPONENT PARTS. PRIOR TO UNDERTAKING RESURFACING AND FINISH, THE PARTS ARE INSPECTED FOR CORRECT DIMENSIONAL TOLERANCES AND FUNCTIONALITY. WE WILL CONTACT YOU BY TELEPHONE TO DISCUSS ANY NON-CONFORMING PARTS OR OTHER ISSUES WE UNCOVER DURING THE DIS-ASSEMBLY PROCESS.

EACH PART IS THEN CLEANED IN A WATER-BASED DETERGENT WITH A PLASTIC BRISTLE BRUSH. THEN THE PARTS ARE CHEMICALLY STRIPPED OF OLD BLUING. IF SIGNIFICANT RUST AND/OR PITTING IS EVIDENT, THE AFFECTED AREA IS BEAD BLASTED WITH 1000 GRIT JAPANESE GLASS. THEN THE AFFECTED AREA IS RESURFACED TO OEM SPECIFICATION. WE STRIVE TO NEVER ALTER THE ORIGINAL OEM "LOOK" OF THE PISTOL. ALL PARTS ARE RESURFACED PRIOR TO HOT BLUING, EXCEPT PINS AND INTERNAL COMPONENTS WHICH TYPICALLY REMAIN UNALTERED.

THE PARTS ARE THEN ULTRASONIC CLEANED USING A HIGH TEMPERATURE CONCENTRATED GREASE REMOVING SOLUTION. THEN THEY ARE BATHED IN ACETONE FOR 15 MINUTES FOLLOWED BY A QUICK DIP IN DE-IONIZED WATER. THEY ARE THEN HOT BLUED IN OUR OWN HOT SALT BLUING TANK FOR 20 MINUTES AT 195 +/- 2 DEGREES FARENHEIT. THEREAFTER, THE PARTS ARE DIPPED IN DE-IONIZED WATER FOLLOWED BY A GEAR OIL BATH. EACH PART IS THEN INDIVIDUALLY CLEANED OF BLUING RUST SCALE USING 0000 STEEL WOOL, SUBJECTED TO A HOT WATER-BASED MILD DETERGENT SCRUB WITH A PLASTIC BRUSH, RINSED AGAIN IN DE-IONIZED WATER, BATHED IN WD-40 AND FINALLY DRIED USING COMPRESSED AIR AND LINT FREE COTTON TOWELS. NOT AS SIMPLE AS YOU THOUGHT, RIGHT?

THEREAFTER THE PISTOL IS RE-ASSEMBLED FROM ITS COMPONENT PARTS, LUBRICATED WITH GUN OIL AND BENCH TESTED. CONFIRMATION IS MADE AT THIS TIME THAT THE PISTOL WILL CYCLE AND EJECT SAAMI CERTIFIED, 50 GRAIN FULL METAL JACKET AMMUNITION. WE USED CUSTOM MADE SAAMI CERTIFIED "BLANK" AMMO FOR THIS MECHANICAL CYCLING PROCEDURE. DO NOT ATTEMPT AT HOME.

THE HOT BLUING SERVICE INCLUDES COMPLETE OEM PERIOD SPECIFIC PACKAGING AND OPERATORS' MANUAL, BARREL CLEANING BRUSH AND ONE OF OUR PSA HATS - WHICH YOU WILL WEAR WITH PRIDE EVERYWHERE YOU GO, RIGHT?

POSTAGE IN BOTH DIRECTIONS IS ARRANGED BY US AND IS BY U.S. PRIORITY MAIL. SIGNATURE IS REQUIRED FOR DELIVERY. 

READY TO SHIP?  CONTACT US BY EMAIL (SALES@PRECISIONSMALLARMS.COM) OR TELEPHONE: 415-640-1094. WE WILL EMAIL YOU DIRECTIONS.

12 MONTH WARRANTY ON THE HOT BLUE FINISH AND ALL INSTALLED PARTS AND LABOR.

PURCHASE THIS SERVICE BY ADDING THIS ITEM TO YOUR SHOPPING CART.

RING US TO DISCUSS. YOU MIGHT BE AMAZED AT WHAT WE CAN DO FOR YOU.

OUR TELEPHONE NUMBER IS: 970-390-5520

SERIAL NUMBER ENGRAVING.

FOR OLD OR NEW .25 CAL FN, PSP OR PSA-25 PISTOL BARRELS.

UP TO 6 LETTERS AND/OR NUMBERS. DEAD CENTER BOTTOM-SIDE OF BARREL.

BARREL IS RE-SURFACED TO FACTORY STANDARDS. FEED RAMP IS POLISHED.

THE SPRING REPLACEMENT SERVICE SHOULD BE PERFORMED EVERY 5-10 YEARS FOR ALL 1931 MODEL 6.35MM FABRIQUE NATIONALE, PSP-25 AND PSA-25 POCKET PISTOLS, 

FOLKS OFTEN UNDERTAKE THIS SERVICE WHEN THEY ACQUIRE/INHERIT A USED 1931 MODEL FN 6.35MM, PSP-25 OR PSA-25 POCKET PISTOL. AND THEY TEND TO DO SO AT THE SAME TIME THAT THEY HOT BLUE THE PISTOL AND PURCHASE SECOND GENERATION, ROUNDED FOLLOWER MAGAZINES.

SCOPE OF SERVICE:

THE PISTOL IS DIS-ASSEMBLED INTO ITS COMPONENT PARTS AND THEN ULTRASONIC CLEANED USING A WATER-BASED CONCENTRATED CLEANER. THEREAFTER EACH PART IS RINSED N DE-IONIZED WATER AND THEN BATHED IN WD-40, BLOWN DRY WITH COMPRESSED AIR AND CLEANED WITH A LINT FREE COTTON CLOTH. WE THEN INSPECT EACH PART FOR CORRECT DIMENSIONAL TOLERANCES AND FUNCTIONALITY. WE WILL CONTACT YOU BY TELEPHONE AT THIS TIME IF WE IDENTIFY PARTS THAT ARE FUNCTIONALLY NON-CONFORMING.

ALL SPRINGS ARE REPLACED WITH NEW OEM SPRINGS MANUFACTURED IN FRANCE.

THE PISTOL IS THEN RE-ASSEMBLED, LUBRICATED, BENCH TESTED AND MECHANICALLY CYCLED WITH SAAMI CERTIFIED DUMMY AMMO (DONT DO THIS AT HOME) AND GUARANTEED FUNCTIONAL WHEN WE SHIP IT BACK TO YOU. 

THE SPRING REPLACEMENT SERVICE INCLUDES COMPLETE OEM PACKAGING, PERIOD CORRECT OPERATORS' MANUAL, BARREL CLEANING BRUSH AND ONE OF OUR PSA HATS - WHICH YOU WILL WEAR PROUDLY WHEREVER YOU GO, RIGHT?

RETURN POSTAGE IS BY U.S. 3 DAY PRIORITY MAIL WITH SIGNATURE REQUIRED FOR DELIVERY. 

QUESTIONS? READY TO GO? EMAIL US AT: SALES@PRECISIONSMALLARMS.COM OR CALL US AT: 415-640-1094. WE WILL PROVIDE YOU WITH WRITTEN DIRECTIONS.

PURCHASE THIS SERVICE BY ADDING THIS ITEM TO YOUR SHOPPIING CART.